2024-06-16 vJunos-switch BGP-EVPN-VXLAN 機能検証
先日リリースされた vJunos-switch について、BGP EVPN VXLAN の検証を実施しました。
このページにラボシナリオとして、コンフィグや確認コマンド、疎通確認のポイントなどをまとめています。
目的
レイヤ 3 インターフェース経由で、同一サブネットの通信が可能であること。
検証環境
EVE-NG Community Edition
Juniper vJunos-switch 23.2R1.14
Cisco CSR1000V 17.3.4a
構成図
- CSR1000V : CSR01,02
- vJunos-switch : vEX01,02
IP アドレッシング
文書用例示アドレス | |||||
---|---|---|---|---|---|
種別 | ネットワーク アドレス | ホスト | インターフェース | ホスト アドレス | 備考 |
グローバルアドレス | 203.0.113.0/30 | vEX01 | ge-0/0/3.0 | 203.0.113.1/30 | |
vEX02 | ge-0/0/3.0 | 203.0.113.2/30 | |||
198.51.100.0/24 | vEX01 | lo0.0 | 198.51.100.1/32 | ||
vEX02 | 198.51.100.1/32 | 198.51.100.2/32 | |||
プライベートアドレス | 192.0.2.0/24 | CSR01 | Gi4.10 | 192.0.2.1/30 | |
Gi4.20 | 192.0.2.5/30 | ||||
CSR02 | Gi4.10 | 192.0.2.2/30 | |||
Gi4.20 | 192.0.2.6/30 |
コンフィギュレーション
ここではプロトコル・ホスト別にコンフィギュレーションを簡単に解説します。
自分でコンフィグを組んでみたい人向けに、デフォルトでは表示しません。
このページのリファレンスに記載した、Cisco のサイトを参考に設定してみると良いでしょう。
CSR01 , 02
プロトコル | CSR01 コンフィグ | CSR02 コンフィグ | 解説 |
---|---|---|---|
IPv4 |
CSR01#show run | s net4 interface GigabitEthernet4 description vEX01_ge-0/0/0 no ip address negotiation auto no mop enabled no mop sysid interface GigabitEthernet4.10 encapsulation dot1Q 10 ip address 192.0.2.1 255.255.255.252 interface GigabitEthernet4.20 encapsulation dot1Q 20 ip address 192.0.2.5 255.255.255.252 |
CSR02#show run | s net4 interface GigabitEthernet4 description vEX02_ge-0/0/0 no ip address negotiation auto no mop enabled no mop sysid interface GigabitEthernet4.10 encapsulation dot1Q 10 ip address 192.0.2.2 255.255.255.252 interface GigabitEthernet4.20 encapsulation dot1Q 20 ip address 192.0.2.6 255.255.255.252 |
vEX01 , 02
プロトコル | vEX01 コンフィグ | vEX01 コンフィグ | 解説 |
---|---|---|---|
インターフェース
(ユーザポート) |
interfaces { ge-0/0/0 { flexible-vlan-tagging; encapsulation flexible-ethernet-services; unit 10 { family ethernet-switching { interface-mode trunk; vlan { members v10; } } } unit 20 { family ethernet-switching { interface-mode trunk; vlan { members v20; } } } } } |
interfaces { ge-0/0/0 { flexible-vlan-tagging; encapsulation flexible-ethernet-services; unit 10 { family ethernet-switching { interface-mode trunk; vlan { members v10; } } } unit 20 { family ethernet-switching { interface-mode trunk; vlan { members v20; } } } } } |
ユーザ収容ポート
通常の trunk 設定に加えて、flexible-vlan tagging と flexible-ethernet-services を設定する |
インターフェース
(ネットワークポート) |
interfaces { ge-0/0/3 { unit 0 { family inet { address 203.0.113.1/30; } } } lo0 { unit 0 { family inet { address 198.51.100.1/32; } } } } |
interfaces { ge-0/0/3 { unit 0 { family inet { address 203.0.113.2/30; } } } lo0 { unit 0 { family inet { address 198.51.100.2/32; } } } } |
OSPF 接続用 |
ルーティング
インスタンス |
routing-instances { EVPN-1 { instance-type mac-vrf; protocols { evpn { encapsulation vxlan; extended-vni-list all; } } vtep-source-interface lo0.0; service-type vlan-based; interface ge-0/0/0.10; route-distinguisher 198.51.100.1:1; vrf-target target:65000:1; vlans { v10 { vlan-id 10; ## ## Warning: requires 'vxlan' license ## vxlan { vni 100010; } } } } EVPN-2 { instance-type mac-vrf; protocols { evpn { encapsulation vxlan; extended-vni-list all; } } vtep-source-interface lo0.0; service-type vlan-based; interface ge-0/0/0.20; route-distinguisher 203.0.113.255:1; vrf-target target:65000:1; vlans { v20 { vlan-id 20; ## ## Warning: requires 'vxlan' license ## vxlan { vni 100020; } } } } } |
routing-instances { EVPN-1 { instance-type mac-vrf; protocols { evpn { encapsulation vxlan; extended-vni-list all; } } vtep-source-interface lo0.0; service-type vlan-based; interface ge-0/0/0.10; route-distinguisher 198.51.100.1:1; vrf-target target:65000:1; vlans { v10 { vlan-id 10; ## ## Warning: requires 'vxlan' license ## vxlan { vni 100010; } } } } EVPN-2 { instance-type mac-vrf; protocols { evpn { encapsulation vxlan; extended-vni-list all; } } vtep-source-interface lo0.0; service-type vlan-based; interface ge-0/0/0.20; route-distinguisher 203.0.113.255:1; vrf-target target:65000:1; vlans { v20 { vlan-id 20; ## ## Warning: requires 'vxlan' license ## vxlan { vni 100020; } } } } } |
instance-type mac-vrf
インスタンスの種類を設定
カプセル化方式を設定
通す VNI を設定
VXLAN Tunnel Endpoint を lo0.0 に設定 トラフィックはこのインターフェースを通るため、疎通が通っていないとサービスが止まる
このインスタンスに属するインターフェースを設定
VRF 識別子の RD を設定
VRF のルートターゲットを設定
dot1q タグを 10 に指定
VNI を 100010 に指定 vlan-id と同一の階層にあるため、vlan-id 10 と紐づくことになる |
ルーティング
オプション |
routing-options { router-id 198.51.100.1; autonomous-system 65000; } |
routing-options { router-id 198.51.100.2; autonomous-system 65000; } |
BGP ルータ ID と AS 番号を指定 |
OSPF |
protocols { ospf { area 0.0.0.0 { interface ge-0/0/3.0 { interface-type p2p; } interface lo0.0; } } } |
protocols { ospf { area 0.0.0.0 { interface ge-0/0/3.0 { interface-type p2p; } interface lo0.0; } } } |
OSPF エリア 0.0.0.0 に属するインターフェースを指定 |
BGP |
protocols { ## ## Warning: requires 'bgp' license ## bgp { group ibgp { type internal; local-address 198.51.100.1; family evpn { signaling; } neighbor 198.51.100.2; } } } |
protocols { ## ## Warning: requires 'bgp' license ## bgp { group ibgp { type internal; local-address 198.51.100.2; family evpn { signaling; } neighbor 198.51.100.1; } } } |
BGP を設定
ピアリングに使うアドレスを lo0 として、OSPF が Up して (アンダーレイ) lo0 アドレスを交換したあとに BGP のピアが Up する (オーバーレイ) ようにしている
BGP でやり取りする情報に EVPN を設定 VXLAN の場合 MAC アドレスなどがやり取りされる |
種別 | vEX01 set コンフィグ | vEX01 set コンフィグ | 解説 |
---|---|---|---|
インターフェース |
set interfaces ge-0/0/0 flexible-vlan-tagging set interfaces ge-0/0/0 encapsulation flexible-ethernet-services set interfaces ge-0/0/0 unit 10 family ethernet-switching interface-mode trunk set interfaces ge-0/0/0 unit 10 family ethernet-switching vlan members v10 set interfaces ge-0/0/0 unit 20 family ethernet-switching interface-mode trunk set interfaces ge-0/0/0 unit 20 family ethernet-switching vlan members v20 set interfaces ge-0/0/3 unit 0 family inet address 203.0.113.1/30 |
set interfaces ge-0/0/0 flexible-vlan-tagging set interfaces ge-0/0/0 encapsulation flexible-ethernet-services set interfaces ge-0/0/0 unit 10 family ethernet-switching interface-mode trunk set interfaces ge-0/0/0 unit 10 family ethernet-switching vlan members v10 set interfaces ge-0/0/0 unit 20 family ethernet-switching interface-mode trunk set interfaces ge-0/0/0 unit 20 family ethernet-switching vlan members v20 set interfaces ge-0/0/3 unit 0 family inet address 203.0.113.2/30 |
|
ルーティング
インスタンス |
set routing-instances EVPN-1 instance-type mac-vrf set routing-instances EVPN-1 protocols evpn encapsulation vxlan set routing-instances EVPN-1 protocols evpn extended-vni-list all set routing-instances EVPN-1 vtep-source-interface lo0.0 set routing-instances EVPN-1 service-type vlan-based set routing-instances EVPN-1 interface ge-0/0/0.10 set routing-instances EVPN-1 route-distinguisher 198.51.100.1:1 set routing-instances EVPN-1 vrf-target target:65000:1 set routing-instances EVPN-1 vlans v10 vlan-id 10 set routing-instances EVPN-1 vlans v10 vxlan vni 100010 set routing-instances EVPN-2 instance-type mac-vrf set routing-instances EVPN-2 protocols evpn encapsulation vxlan set routing-instances EVPN-2 protocols evpn extended-vni-list all set routing-instances EVPN-2 vtep-source-interface lo0.0 set routing-instances EVPN-2 service-type vlan-based set routing-instances EVPN-2 interface ge-0/0/0.20 set routing-instances EVPN-2 route-distinguisher 203.0.113.255:1 set routing-instances EVPN-2 vrf-target target:65000:1 set routing-instances EVPN-2 vlans v20 vlan-id 20 set routing-instances EVPN-2 vlans v20 vxlan vni 100020 |
set routing-instances EVPN-1 instance-type mac-vrf set routing-instances EVPN-1 protocols evpn encapsulation vxlan set routing-instances EVPN-1 protocols evpn extended-vni-list all set routing-instances EVPN-1 vtep-source-interface lo0.0 set routing-instances EVPN-1 service-type vlan-based set routing-instances EVPN-1 interface ge-0/0/0.10 set routing-instances EVPN-1 route-distinguisher 198.51.100.1:1 set routing-instances EVPN-1 vrf-target target:65000:1 set routing-instances EVPN-1 vlans v10 vlan-id 10 set routing-instances EVPN-1 vlans v10 vxlan vni 100010 set routing-instances EVPN-2 instance-type mac-vrf set routing-instances EVPN-2 protocols evpn encapsulation vxlan set routing-instances EVPN-2 protocols evpn extended-vni-list all set routing-instances EVPN-2 vtep-source-interface lo0.0 set routing-instances EVPN-2 service-type vlan-based set routing-instances EVPN-2 interface ge-0/0/0.20 set routing-instances EVPN-2 route-distinguisher 203.0.113.255:1 set routing-instances EVPN-2 vrf-target target:65000:1 set routing-instances EVPN-2 vlans v20 vlan-id 20 set routing-instances EVPN-2 vlans v20 vxlan vni 100020 |
|
ルーティング
オプション |
set routing-options router-id 198.51.100.1 set routing-options autonomous-system 65000 |
set routing-options router-id 198.51.100.2 set routing-options autonomous-system 65000 |
|
OSPF |
set protocols ospf area 0.0.0.0 interface ge-0/0/3.0 interface-type p2p set protocols ospf area 0.0.0.0 interface lo0.0 |
set protocols ospf area 0.0.0.0 interface ge-0/0/3.0 interface-type p2p set protocols ospf area 0.0.0.0 interface lo0.0 |
|
BGP |
set protocols bgp group ibgp type internal set protocols bgp group ibgp local-address 198.51.100.1 set protocols bgp group ibgp family evpn signaling set protocols bgp group ibgp neighbor 198.51.100.2 |
set protocols bgp group ibgp type internal set protocols bgp group ibgp local-address 198.51.100.2 set protocols bgp group ibgp family evpn signaling set protocols bgp group ibgp neighbor 198.51.100.1 |
疎通確認
確認 | CSR01 | CSR02 | 備考 |
---|---|---|---|
疎通確認 |
CSR01#ping 192.0.2.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.0.2.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/5 ms CSR01# CSR01#traceroute 192.0.2.2 Type escape sequence to abort. Tracing the route to 192.0.2.2 VRF info: (vrf in name/id, vrf out name/id) 1 192.0.2.2 25 msec * 4 msec CSR01# CSR01#ping 192.0.2.6 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.0.2.6, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/5 ms CSR01# CSR01#traceroute 192.0.2.6 Type escape sequence to abort. Tracing the route to 192.0.2.6 VRF info: (vrf in name/id, vrf out name/id) 1 192.0.2.6 5 msec * 5 msec CSR01# CSR01#show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 192.0.2.1 - 5000.0003.0003 ARPA GigabitEthernet4.10 Internet 192.0.2.2 91 5000.0004.0003 ARPA GigabitEthernet4.10 Internet 192.0.2.5 - 5000.0003.0003 ARPA GigabitEthernet4.20 Internet 192.0.2.6 91 5000.0004.0003 ARPA GigabitEthernet4.20 |
CSR02#ping 192.0.2.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.0.2.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 2/3/4 ms CSR02# CSR02#traceroute 192.0.2.1 Type escape sequence to abort. Tracing the route to 192.0.2.1 VRF info: (vrf in name/id, vrf out name/id) 1 192.0.2.1 65 msec * 4 msec CSR02# CSR02#ping 192.0.2.5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.0.2.5, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/3 ms CSR02# CSR02#traceroute 192.0.2.5 Type escape sequence to abort. Tracing the route to 192.0.2.5 VRF info: (vrf in name/id, vrf out name/id) 1 192.0.2.5 4 msec * 4 msec CSR02# CSR02#show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 192.0.2.1 109 5000.0003.0003 ARPA GigabitEthernet4.10 Internet 192.0.2.2 - 5000.0004.0003 ARPA GigabitEthernet4.10 Internet 192.0.2.5 109 5000.0003.0003 ARPA GigabitEthernet4.20 Internet 192.0.2.6 - 5000.0004.0003 ARPA GigabitEthernet4.20 |
アンダーレイ・オーバーレイ動作確認
プロトコル | CSR01 | CSR02 | 備考 |
---|---|---|---|
OSPF
アンダーレイ |
root@vEX01> show ospf neighbor Address Interface State ID Pri Dead 203.0.113.2 ge-0/0/3.0 Full 198.51.100.2 128 32 root@vEX01> |
root@vEX02> show ospf neighbor Address Interface State ID Pri Dead 203.0.113.1 ge-0/0/3.0 Full 198.51.100.1 128 35 root@vEX02>
|
|
BGP
オーバーレイ |
root@vEX01> show bgp summary Warning: License key missing; requires 'bgp' license Threading mode: BGP I/O Default eBGP mode: advertise - accept, receive - accept Groups: 1 Peers: 1 Down peers: 0 Table Tot Paths Act Paths Suppressed History Damp State Pending bgp.evpn.0 2 2 0 0 0 0 Peer AS InPkt OutPkt OutQ Flaps Last Up/Dwn State|#Active/Received/Accepted/Damped... 198.51.100.2 65000 332 332 0 0 2:21:58 Establ bgp.evpn.0: 2/2/2/0 EVPN-1.evpn.0: 2/2/2/0 __default_evpn__.evpn.0: 0/0/0/0 EVPN-2.evpn.0: 2/2/2/0 root@vEX01> |
root@vEX02> show bgp summary Warning: License key missing; requires 'bgp' license Threading mode: BGP I/O Default eBGP mode: advertise - accept, receive - accept Groups: 1 Peers: 1 Down peers: 0 Table Tot Paths Act Paths Suppressed History Damp State Pending bgp.evpn.0 2 2 0 0 0 0 Peer AS InPkt OutPkt OutQ Flaps Last Up/Dwn State|#Active/Received/Accepted/Damped... 198.51.100.1 65000 331 328 0 0 2:21:27 Establ bgp.evpn.0: 2/2/2/0 EVPN-1.evpn.0: 2/2/2/0 __default_evpn__.evpn.0: 0/0/0/0 EVPN-2.evpn.0: 2/2/2/0 root@vEX02> |
|
エントリ確認
プロトコル | CSR01 | CSR02 | 備考 |
---|---|---|---|
OSPF |
root@vEX01> show route protocol ospf inet.0: 5 destinations, 5 routes (5 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations + = Active Route, - = Last Active, * = Both 198.51.100.2/32 *[OSPF/10] 02:27:46, metric 1 > to 203.0.113.2 via ge-0/0/3.0 224.0.0.5/32 *[OSPF/10] 03:50:32, metric 1 MultiRecv inet6.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations bgp.evpn.0: 8 destinations, 8 routes (8 active, 0 holddown, 0 hidden) EVPN-1.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) EVPN-2.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) root@vEX01> |
root@vEX02> show route protocol ospf inet.0: 5 destinations, 5 routes (5 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations + = Active Route, - = Last Active, * = Both 198.51.100.1/32 *[OSPF/10] 02:28:25, metric 1 > to 203.0.113.1 via ge-0/0/3.0 224.0.0.5/32 *[OSPF/10] 03:51:04, metric 1 MultiRecv inet6.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations bgp.evpn.0: 8 destinations, 8 routes (8 active, 0 holddown, 0 hidden) EVPN-1.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) EVPN-2.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) root@vEX02> |
OSPF はアンダーレイで動作するため、対向側 lo0 のアドレスを受信しているか確認します |
BGP |
root@vEX01> show route protocol bgp Warning: License key missing; requires 'bgp' license inet.0: 5 destinations, 5 routes (5 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations inet6.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations bgp.evpn.0: 8 destinations, 8 routes (8 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 2:198.51.100.1:1::0::50:00:00:04:00:03/304 MAC/IP *[BGP/170] 00:01:14, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0, Push 6250 2:203.0.113.255:1::0::50:00:00:04:00:03/304 MAC/IP *[BGP/170] 00:01:12, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0, Push 6251 3:198.51.100.1:1::0::198.51.100.2/248 IM *[BGP/170] 02:15:23, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0 3:203.0.113.255:1::0::198.51.100.2/248 IM *[BGP/170] 01:43:11, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0 EVPN-1.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 2:198.51.100.1:1::0::50:00:00:04:00:03/304 MAC/IP *[BGP/170] 00:01:14, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0, Push 6250 2:203.0.113.255:1::0::50:00:00:04:00:03/304 MAC/IP *[BGP/170] 00:01:12, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0, Push 6251 3:198.51.100.1:1::0::198.51.100.2/248 IM *[BGP/170] 02:15:23, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0 3:203.0.113.255:1::0::198.51.100.2/248 IM *[BGP/170] 01:43:11, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0 EVPN-2.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 2:198.51.100.1:1::0::50:00:00:04:00:03/304 MAC/IP *[BGP/170] 00:01:14, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0, Push 6250 2:203.0.113.255:1::0::50:00:00:04:00:03/304 MAC/IP *[BGP/170] 00:01:12, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0, Push 6251 3:198.51.100.1:1::0::198.51.100.2/248 IM *[BGP/170] 01:44:59, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0 3:203.0.113.255:1::0::198.51.100.2/248 IM *[BGP/170] 01:43:11, localpref 100, from 198.51.100.2 AS path: I, validation-state: unverified > to 203.0.113.2 via ge-0/0/3.0 root@vEX01> |
root@vEX02> show route protocol bgp Warning: License key missing; requires 'bgp' license inet.0: 5 destinations, 5 routes (5 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations inet6.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden) Limit/Threshold: 1048576/1048576 destinations bgp.evpn.0: 8 destinations, 8 routes (8 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 2:198.51.100.1:1::0::50:00:00:03:00:03/304 MAC/IP *[BGP/170] 00:00:06, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0, Push 6250 2:203.0.113.255:1::0::50:00:00:03:00:03/304 MAC/IP *[BGP/170] 00:00:04, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0, Push 6251 3:198.51.100.1:1::0::198.51.100.1/248 IM *[BGP/170] 02:14:15, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0 3:203.0.113.255:1::0::198.51.100.1/248 IM *[BGP/170] 01:43:49, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0 EVPN-1.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 2:198.51.100.1:1::0::50:00:00:03:00:03/304 MAC/IP *[BGP/170] 00:00:06, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0, Push 6250 2:203.0.113.255:1::0::50:00:00:03:00:03/304 MAC/IP *[BGP/170] 00:00:04, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0, Push 6251 3:198.51.100.1:1::0::198.51.100.1/248 IM *[BGP/170] 02:14:15, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0 3:203.0.113.255:1::0::198.51.100.1/248 IM *[BGP/170] 01:43:49, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0 EVPN-2.evpn.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 2:198.51.100.1:1::0::50:00:00:03:00:03/304 MAC/IP *[BGP/170] 00:00:06, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0, Push 6250 2:203.0.113.255:1::0::50:00:00:03:00:03/304 MAC/IP *[BGP/170] 00:00:04, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0, Push 6251 3:198.51.100.1:1::0::198.51.100.1/248 IM *[BGP/170] 01:42:05, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0 3:203.0.113.255:1::0::198.51.100.1/248 IM *[BGP/170] 01:42:05, localpref 100, from 198.51.100.1 AS path: I, validation-state: unverified > to 203.0.113.1 via ge-0/0/3.0 root@vEX02>
|
BGP はオーバーレイとして、対向側の MAC アドレスを受信しているか確認します |
MAC |
root@vEX01> show ethernet-switching table MAC flags (S - static MAC, D - dynamic MAC, L - locally learned, P - Persistent static SE - statistics enabled, NM - non configured MAC, R - remote PE MAC, O - ovsdb MAC, B - Blocked MAC) Ethernet switching table : 2 entries, 2 learned Routing instance : EVPN-1 Vlan MAC MAC GBP Logical SVLBNH/ Active name address flags tag interface VENH Index source v10 50:00:00:03:00:03 D ge-0/0/0.10 v10 50:00:00:04:00:03 DR vtep.32768 198.51.100.2 MAC flags (S - static MAC, D - dynamic MAC, L - locally learned, P - Persistent static SE - statistics enabled, NM - non configured MAC, R - remote PE MAC, O - ovsdb MAC, B - Blocked MAC) Ethernet switching table : 2 entries, 2 learned Routing instance : EVPN-2 Vlan MAC MAC GBP Logical SVLBNH/ Active name address flags tag interface VENH Index source v20 50:00:00:03:00:03 D ge-0/0/0.20 v20 50:00:00:04:00:03 DR vtep.32772 198.51.100.2 root@vEX01> |
root@vEX02> show ethernet-switching table MAC flags (S - static MAC, D - dynamic MAC, L - locally learned, P - Persistent static SE - statistics enabled, NM - non configured MAC, R - remote PE MAC, O - ovsdb MAC, B - Blocked MAC) Ethernet switching table : 2 entries, 2 learned Routing instance : EVPN-1 Vlan MAC MAC GBP Logical SVLBNH/ Active name address flags tag interface VENH Index source v10 50:00:00:03:00:03 DR vtep.32768 198.51.100.1 v10 50:00:00:04:00:03 D ge-0/0/0.10 MAC flags (S - static MAC, D - dynamic MAC, L - locally learned, P - Persistent static SE - statistics enabled, NM - non configured MAC, R - remote PE MAC, O - ovsdb MAC, B - Blocked MAC) Ethernet switching table : 2 entries, 2 learned Routing instance : EVPN-2 Vlan MAC MAC GBP Logical SVLBNH/ Active name address flags tag interface VENH Index source v20 50:00:00:03:00:03 DR vtep.32771 198.51.100.1 v20 50:00:00:04:00:03 D ge-0/0/0.20 root@vEX02> |
MAC アドレステーブルでローカルの ge-0/0/0.10 , 20 にエントリがあること、リモートのエントリが vtep で学習できていることを確認します |
動作確認 - ホスト別コマンドリスト
CSR01 , 02
- ping
- traceroute
- show ip arp
vEX01
- show route protocol ospf
- show route protocol bgp
- show ethernet-switching table
リファレンス
Juniper QFXで実践! EVPN/VXLANの実力値