2024-04-03 Cisco StackWise Virtual まとめ

提供：hkatou_Lab

Cisco Catalyst StackWise Virtual についてまとめました。

設定ガイドライン

初期リリースの制限

  • すべてのプラットフォームで、初期リリースの IOS-XE では StackWise Virtual がサポートされません
    • 例) C9400X-SUP-2 は、ハードウェアとして 17.7.1 から使用できますがスタンドアローンのみで、17.9.1 以降で StackWise Virtual がサポートされます
  • コマンドは入るが動作しない / 保証されない、といったバージョンもある

機能追加

  • C9500 のアップリンク モジュールで、SVL が使用できないリリースがありました
  • 新リリースではサポートされます (サポート マトリックス参照)

SVL は 8 ポートまで [1]

  • UADP ASIC 搭載機の SVL 増速 / DAD 設定は再起動が必要なため、初期導入時に SVL を最大の 8 ポート + DAD 1 ポートまで接続してしまうのがおすすめ
    • アップリンク本数増加が将来的に必要なければ、SVL 本数は少なくて良いです
  • Silicon One ASIC 搭載機 (C9500X , C9600X) は再起動が必要なくなりました

SVL を設定できるポートには制限があります

  • C9500-16X , 40X : 10G はアップリンクモジュールと混在可能、40G は混在不可
    • 使用可能なバージョンに注意
    • 40G アップリンクモジュールは、オンボードの 10G と速度が異なるため、SVL に混在できません
  • C9500-32C : 1-16 ポートのみ設定可能
  • ブレークアウト , QSA アダプタは基本的に SVL , DAD ポートで使用できません [2]
    • C9500 は QSA アダプタを使用しても、SVL に使用できません
    • C9600 は例外で QSA アダプタを使用して、SVL に使用できます [3]
    • QSA アダプタ : QSFP -> SFP+ に形状変換するトランシーバ
  • 10G 以上の速度で SVL/DAD はサポートされ、1G は SVL で動作せず、DAD には対応します

SVL の速度は同一である必要があります

  • 10G / 25G 両対応ポートでは、トランシーバを搭載することでモードが確定するため、25G の場合は搭載しないと設定ができません

C9500-24Y4C , 48Y4C で 25G ポートを SVL に使用できます [4]

  • 100G ポートを温存したい場合に有効

Network Advantage ライセンスが必要です [5]

  • 旧世代の WS-C4500X は IP Base でも VSS が組めていましたが、C9500 は Network Advantage (IP Services 相当) になります
    • リプレース時の金額が異なるため注意
    • 例) Catalyst 4500X VSS IP Base -> Catalyst 9500 SWV Network Advantage
  • Layer2 スイッチで StackWise Virtual を入れるのは、ライセンス費用が高くつきます
    • C9300X Stack などが使用できないか検討したほうが良いでしょう
  • C9404R + SUP1 では、さらに C9400-SUP-UPG-LIC= ライセンスが必要 [6]

Vlan ID [7]

  • 4094 を SWV で使用するため、ユーザは使用できません

その他の制限

例 : Restrictions for Cisco StackWise Virtual IOS-XE 17.3

  • 機種により異なるため、使う機種 + IOS-XE バージョンのドキュメントを参照してください

StackWise Virtual サポート マトリックス

Catalyst 3850 / 9400 / 9400X /9500 / 9500X / 9600 / 9600X StackWise Virtual サポート マトリックス
ファミリ 機種 IOS-XE

最小サポート

SWV サポート ライセンス

Network Essencials では動作しません

SVL/DAD

ポート番号制限

クアッド スーパーバイザ with RPR 備考
C3850 WS-C3850-12XS

WS-C3850-24XS

WS-C3850-48XS

12XS , 24XS : 3.7.1E (15.2(3)E1) [8]

48XS : 3.7.2E (15.2(3)E2) [9]

16.3.3 : 初期リリース

16.5.1a : 非サポート化

16.6.1 : 再導入

IP Base

IP Services

SVL/DAD はアップリンクモジュール/ポートで設定不可 [10] - 16.12 までは 3850XS でも検証可能

ラボで模擬させるときに便利

C9400 C9400-SUP-1

C9400-SUP-1-XL

SUP-1 : 16.6.1 [11]

SUP1-XL : 16.6.2 [12]

16.9.1-

9410R は 16.11.1-

Network Advantage

C9400-SUP-UPG-LIC=

- 非対応 なぜか C9400-SUP-1 のみ追加ライセンスが必要
C9400X C9400X-SUP-2

C9400X-SUP-2XL

17.7.1 [13] 17.9.1- [14] Network Advantage - 非対応 17.9.1- で SWV が実装された [15] [16]
  • Release-notes と Configuration Guide の Feature History に SWV の記載が無いがサポートしているようだ


Quad SUP は C9400 で非対応 [17] のため注意

C9500 C9500-12Q

C9500-16X C9500-24Q C9500-40X

24Q : 16.5.1a

12Q , 40X : 16.6.1 [18]

16.6.1 [19] Network Advantage -16.10.x : ネットワーク モジュールで使用不可

16.11.x- : ネットワーク モジュールも SVL/DAD に使用可能

- よくみるやつ

EoS が出てるので今後のデプロイは少なくなる

C9500H C9500-32C

C9500-32QC C9500-48Y4C

C9500-24Y4C

16.8.1a [20] 16.10.1 [21] Network Advantage 32C : 1-16 ポートのみ [22]

32QC : ネイティブ 40/100G ポートのみ [23]

- 今後の主流

24Y or 48Y の 100G で SVL を組むと 100G がもったいないため、25G x4 or 8 で組むのがおすすめ

  • 25G 対応機器はまだまだ少ない


32QC はデフォルトで物理ポート番号 1-24 が 40G , 25,27,29,31 が 100G として動作する [24]

  • SVL としては 1-24 番ポートに QSFP-100G を搭載できない


32C は 1-16 番ポートしか SVL が組めない [25] ため、注意

C9500X C9500X-28C8D 17.7.1 [26] 17.10.1 [27] Network Advantage - - Silicon One ASIC 搭載機

17.12.x の長期メンテナンス版からちゃんと動くか ?

C9500X-60L4D 17.10.1b [28] 17.11.1 [29] Network Advantage - - Silicon One ASIC 搭載機

17.12.x の長期メンテナンス版からちゃんと動くか ?

C9600 C9600-SUP-1 16.11.1 [30] 16.12.1 Network Advantage - 17.2.x- 以降 [31] DAD はラインカード型式に制限あり [32]
C9600X C9600X-SUP-2 17.7.1 [33] 17.10.1 [34] Network Advantage - 2023/08/30

未サポート [35]

Silicon One ASIC 搭載機

17.12.x の長期メンテナンス版からちゃんと動くか ?

その他リンク

Catalyst 9600のクアッドスーパーバイザStackwise仮想セットアップへの移行

Catalyst：Stackwise Virtual の設定

Cisco Catalyst 9000 Platform StackWise Virtual White Paper

更新履歴

2023-08-30 : 初版

2024-01-24 : 各機種の IOS-XE 最小サポート Ver を追加

2024-04-03 : 各種制限の引用を追加

引用

  1. ↑ Cisco StackWise Virtual on Cisco Catalyst 9500 Series Switches You can configure up to 8 SVLs in a Cisco StackWise Virtual solution using Cisco Catalyst 9500 Series Switches or Cisco Catalyst 9500 Series High Performance Switches.
  2. ↑ Limitations and Restrictions On Cisco Catalyst 9500 Series Switches, when Cisco StackWise Virtual is configured, breakout ports using 4X10G breakout cables, or the Cisco QSFP to SFP or SFP+ Adapter (QSA) module can only be used as data ports; they cannot be used to configure StackWise Virtual links (SVLs) or dual-active detective (DAD) links.
  3. ↑ High Availability Configuration Guide, Cisco IOS XE Dublin 17.10.x (Catalyst 9600 Switches) Restrictions for Cisco StackWise Virtual In a Cisco StackWise Virtual solution, QSA along with 10G interfaces can be used as data ports or SVL or DAD links. In a Cisco StackWise Virtual solution, QSA along with 1G interfaces can be used as data ports or DAD links. SVL links are not supported on 1G interfaces.
  4. ↑ Cisco StackWise Virtual on Cisco Catalyst 9500 Series Switches You can establish SVLs using 40G or 10G Ethernet connections on Cisco Catalyst 9500 Series Switches and 100G, 40G, 25G and 10G Ethernet connections on Cisco Catalyst 9500 Series High Performance Switches.
  5. ↑ Restrictions for Cisco StackWise Virtual Cisco StackWise Virtual configuration commands will be recognised only on a switch running Network Advantage license. The configuration commands will not be recognised on a Network Essentials license.
  6. ↑ Software Features in Cisco IOS XE Fuji 16.9.1 Supervisor Modules Cisco Catalyst 9400 Series Supervisor 1 Module (C9400-SUP-1). The feature requires a special, additional, C9400-SUP-UPG-LIC= license with this supervisor module.
  7. ↑ Restrictions for Cisco StackWise Virtual When deploying Cisco StackWise Virtual, ensure that VLAN ID 4094 is not used anywhere on the network. All inter-chassis system control communication between stack members is carried over the reserved VLAN ID 4094 from the global range.
  8. ↑ What’s New in Cisco IOS XE Release 3.7.1E New multi-Gigabit stackable switch model that support up to 36 ports at 1G and 12 ports at 100M, 1G, 2.5G, 5G and 10G. – WS-C3850-24XU-L – WS-C3850-24XU-S – WS-C3850-24XU-E – WS-C3850-12X48U-L – WS-C3850-12X48U-S – WS-C3850-12X48U-E – WS-C3850-12XS-S – WS-C3850-16XS-S – WS-C3850-24XS-S – WS-C3850-32XS-S – WS-C3850-12XS-E – WS-C3850-16XS-E – WS-C3850-24XS-E – WS-C3850-32XS-E
  9. ↑ What’s New in Cisco IOS XE Release 3.7.2E New switch models: – WS-C3850-48XS-S – WS-C3850-48XS-F-S – WS-C3850-48XS-E – WS-C3850-48XS-F-E
  10. ↑ Restrictions for Cisco StackWise Virtual Configuring SVLs on any of the network modules is not supported. Dual-Active Detection is not supported on the uplink ports of the switch.
  11. ↑ Supported Hardware on Cisco Catalyst 9400 Series Switches Table 2 Supported Hardware on Cisco Catalyst 9400 Series Switches C9400-SUP-1
  12. ↑ Hardware Features in Cisco IOS XE Everest 16.6.2 Feature Name C9400-SUP-1XL Description and License Level Information Cisco Catalyst 9400 Series Supervisor 1XL Module This supervisor module is supported on C9407R, C9410R chassis.
  13. ↑ Hardware Features in Cisco IOS XE Cupertino 17.7.1 Feature Name Cisco Catalyst 9400 Series Supervisor 2 Module (C9400X-SUP-2) Description and Documentation Link Hardware Features: Supported on Cisco Catalyst C9404R, C9407R, and C9410R chassis. Feature Name Cisco Catalyst 9400 Series Supervisor 2XL Module (C9400X-SUP-2XL) Description and Documentation Link Hardware Features: Supported on Cisco Catalyst C9404R, C9407R, and C9410R chassis.
  14. ↑ Restrictions for Cisco StackWise Virtual Cisco StackWise Virtual is also supported on Cisco Catalyst 9400X Seried Supervisor 2 Module (C9400X-SUP-2) and Cisco Catalyst 9400 Series Supervisor 2XL Module (C9400X-SUP-2XL). Line cards C9400-LC-48HX and C9400-LC-48XS must be used with a C9400X Supervisor (for example, C9400X-SUP-2XL or C9400X-SUP-2).
  15. ↑ Software Features in Cisco IOS XE Cupertino 17.9.1 Software Features in Cisco IOS XE Cupertino 17.9.1 SVL support on uplink and downlink with 9400X From Cisco IOS XE Cupertino 17.9.1, the SVL and DAD links are supported on the following SUP-2 and SUP2-XL and the already listed line cards:
  16. ↑ High Availability Configuration Guide, Cisco IOS XE Cupertino 17.9.x (Catalyst 9400 Switches) Restrictions for Cisco StackWise Virtual Cisco StackWise Virtual is also supported on Cisco Catalyst 9400X Seried Supervisor 2 Module (C9400X-SUP-2) and Cisco Catalyst 9400 Series Supervisor 2XL Module (C9400X-SUP-2XL).
  17. ↑ Restrictions for Cisco StackWise Virtual Cisco StackWise Virtual can be configured only on one supervisor module per chassis.
  18. ↑ Hardware Features in Cisco IOS XE Everest 16.6.1 Feature Name 40-Gigabit Ethernet QSFP and 10-Gigabit Ethernet SFP Switch Models C9500-12Q C9500-40X-2Q C9500-40X C9500-48X Description These Cisco Catalyst 9500 Series Switches are supported: C9500-12Q—12 40-Gigabit Ethernet QSFP ports and two power supply slots C9500-40X-2Q—40 10-Gigabit Ethernet SFP ports and a 2-Port 40-Gigabit Ethernet (QSFP) network module on uplink ports; and two power supply slots C9500-40X—40 10-Gigabit Ethernet SFP ports and two power supply slots; support for optional network modules on uplink ports — 8-Port 10 Gigabit Ethernet (SFP) and 2-Port 40 Gigabit Ethernet (QSFP) C9500-48X—40 10-Gigabit Ethernet SFP ports and an 8-Port 10-Gigabit Ethernet (SFP) network module on uplink ports; and two power supply slots
  19. ↑ Feature History for Cisco StackWise Virtual Cisco IOS XE Everest 16.6.1 Cisco StackWise Virtual Support for this feature was introduced only on the C9500-12Q, C9500-16X, C9500-24Q, C9500-40X models of the Cisco Catalyst 9500 Series Switches.
  20. ↑ Hardware Features Introduced on Cisco Catalyst 9500 Series Switches-High Performance Feature Name Cisco Catalyst 9500 Series Switches - High Performance Description High Performance models introduced in the series: C9500-32C This model has 32 QSFP28 ports that support 40/100 GigabitEthernet connectivity and two power supply slots. C9500-32QC This model has 32 QSFP28 ports, where you can have 24 ports that support 40-GigabitEthernet connectivity and 4 ports that support 100-GigabitEthernet connectivity, OR 32 ports that support 40-GigabitEthernet connectivity, OR 16 ports that support 100-GigabitEthernet connectivity, and two power supply slots. C9500-48Y4C This model has 48 SFP28 ports that support 1/10/25-GigabitEthernet connectivity, four QSFP uplink ports that support 40/100 -GigabitEthernet connectivity, and two power supply slots. C9500-24Y4C The model has 24 SFP28 ports that support 1/10/25-GigabitEthernet connectivity, four QSFP uplink ports that support 40/100-GigabitEthernet connectivity, and two power supply slots.
  21. ↑ Feature History for Cisco StackWise Virtual Cisco IOS XE Gibraltar 16.10.1 Cisco StackWise Virtual Support for this feature was introduced on the C9500-32C, C9500-32QC, C9500-48Y4C, and C9500-24Y4C models of the Cisco Catalyst 9500 Series Switches.
  22. ↑ Restrictions for Cisco Catalyst 9500 Series High Performance Switches On C9500-32C switches, you can configure SVL and DAD only on interfaces numbered 1-16 on the front panel of the switch.
  23. ↑ Restrictions for Cisco Catalyst 9500 Series High Performance Switches On C9500-32QC, you can configure SVL and DAD only on native 100G and 40G interfaces (default configuration ports). You cannot configure SVL and DAD on converted 100G and 40G interfaces.
  24. ↑ Configuring Hundred GigabitEthernet Interfaces on C9500-32QC The default status of the 40 GigabitEthernet and 100 GigabitEthernet interfaces is as below: Port numbers 1 to 24 are active as 40 GigabitEthernet interfaces, by default. The corresponding 100 GigabitEthernet interfaces for these ports become inactive. To enable the 100 GigabitEthernet interfaces - 33 to 44, use the enable command on the 40 GigabitEthernet interface. Port numbers 25 to 32 are active as 100 GigabitEthernet interfaces, by default. The corresponding 40 GigabitEthernet interfaces for these ports become inactive. To enable the 40 GigabitEthernet interfaces on these ports - 25 to 32, use the no enable command on the 100 GigabitEthernet interface.
  25. ↑ Restrictions for Cisco Catalyst 9500 Series High Performance Switches On C9500-32C switches, you can configure SVL and DAD only on interfaces numbered 1-16 on the front panel of the switch.
  26. ↑ Hardware Features in Cisco IOS XE Cupertino 17.7.1 Feature Name Cisco Catalyst 9500X Series Switches (C9500X-28C8D) Description and Documentation Link The following new model is introduced in the series: C9500X-28C8D: 28x100G QSFP28 and 8x400G QSFP-DD ports; 2 power supply slots
  27. ↑ Feature History for Cisco StackWise Virtual Cisco IOS XE Dublin 17.10.1 Cisco StackWise Virtual Support for this feature was introduced on the C9500X-28C8D model of Cisco Catalyst 9500 Series Switches.
  28. ↑ Hardware Features in Cisco IOS XE Dublin 17.10.1b Feature Name Cisco Catalyst 9500X Series Switches (C9500X-60L4D) Description The following model is introduced in the series: C9500X-60L4D: 60x50G SFP56 and 4x400G QSFP-DD ports; 2 power supply slots
  29. ↑ Software Features in Cisco IOS XE Dublin 17.11.1 Feature Name Cisco StackWise Virtual Description Starting with this release, the feature is supported on the C9500X-60L4D model of Cisco Catalyst 9500X Series Switches.
  30. ↑ Supported Hardware on Cisco Catalyst 9600 Series Switches Supervisor Modules C9600-SUP-1 Description Cisco Catalyst 9600 Series Supervisor 1 Module This supervisor module is supported on the C9606R chassis
  31. ↑ High Availability Configuration Guide, Cisco IOS XE Amsterdam 17.2.x (Catalyst 9600 Switches) Prerequisites for Quad-Supervisor with RPR The minimum required software version for all the supervisors in the Quad-Supervisor setup is Cisco IOS XE Amsterdam 17.2.1 .
  32. ↑ Feature History for Cisco StackWise Virtual Cisco IOS XE Amsterdam 17.2.1 Cisco StackWise Virtual: Interface and line card configurations DAD links are now supported for the following interface and line card configurations: 1G interface on a C9600-LC-48TX line card. 1G interface if configured between a C9600-LC-48TX line card and either a C9600-LC-48YL line card or a C9600-LC-24C line card. 1G interface and 10G interface if configured between two C9600-LC-48YL line cards or between two C9600-LC-24C line cards. 1G interface and 10G interface if configured between a C9600-LC-48YL line card and a C9600-LC-24C line card.
  33. ↑ Hardware Features in Cisco IOS XE Cupertino 17.7.1 Feature Name Cisco Catalyst 9600 Series Supervisor Engine 2 (C9600X-SUP-2) Description and Documentation Link This supervisor engine is supported on Cisco Catalyst 9600 Series 6 Slot Chassis (C9606R).
  34. ↑ Feature History for Cisco StackWise Virtual Cisco IOS XE Dublin 17.10.1 Cisco StackWise Virtual Support for this feature was introduced on the Cisco Catalyst 9600 Series Supervisor 2 Module (C9600X-SUP-2).
  35. ↑ Restrictions for Cisco StackWise Virtual The following are the restrictions for Cisco Catalyst 9600 Series Supervisor 2 Module (C9600X-SUP-2): ・C9600X-SUP-2 on a C9606R chassis does not support Quad-Supervisor with RPR.
「http://hkatou.net/index.php?title=2024-04-03_Cisco_StackWise_Virtual_まとめ&oldid=2238」から取得